{"id":5348,"date":"2025-11-01T23:11:09","date_gmt":"2025-11-01T22:11:09","guid":{"rendered":"https:\/\/dinamobesturing.nl\/software\/dinamoconfig-1-32\/"},"modified":"2026-04-28T13:17:25","modified_gmt":"2026-04-28T11:17:25","slug":"dinamoconfig-1-32","status":"publish","type":"software","link":"https:\/\/dinamobesturing.nl\/en\/software\/dinamoconfig-1-32\/","title":{"rendered":"DinamoConfig 1.32"},"content":{"rendered":"\n<h2 class=\"wp-block-heading\" id=\"Wijzigingen_t\\.o.v._DinamoConfig_1.31\">Changes compared to DinamoConfig 1.31<a href=\"https:\/\/dinamousers.net\/DinamoConfig+Release+Notes+1.32_nl#Wijzigingen_t.o.v._DinamoConfig_1.31\" target=\"_blank\" rel=\"noopener\"><\/a><\/h2>\n\n<p>With DinamoConfig 1.32, you can request an analysis of the clock (synchronization between TM44s and TM-Hs). For now, this check is located behind the Master\/Slave check that you can perform if you choose All-TMxx. A prerequisite is that the firmware of your TM44s is at least 1.21 and your TM-Hs is 5.21  <\/p>\n\n<p>The TM44\/TM-H slave can report 4 states:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>Clock OK<\/li>\n\n\n\n<li>No Clock (occurs, for example, if the clock bus is short-circuited or interrupted)<\/li>\n\n\n\n<li>Bad Clock (means the clock is very poor, e.g., only 1 wire connected; Dinamo will barely function. Also occurs if the clock polarity is reversed)<\/li>\n\n\n\n<li>Degraded Clock (means the clock signal is getting through but shows timing errors; Dinamo will likely function, but possibly with unclear issues. This may indicate poor cables or errors with terminating resistors)<\/li>\n<\/ul>\n\n<p>The TM44 master can report 2 states:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>Clock OK<\/li>\n\n\n\n<li>No Clock (occurs, for example, if the clock bus is short-circuited)<\/li>\n<\/ul>\n\n<p>The TM-H master will always report clock-ok because it cannot perform a hardware check. When using a combination of TM44s and TM-Hs, it is strongly recommended to always choose a TM44 as the master. <\/p>\n","protected":false},"featured_media":0,"template":"","meta":{"_acf_changed":false},"software-product":[268],"class_list":["post-5348","software","type-software","status-publish","hentry","software-product-legacy"],"acf":[],"jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/software\/5348","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/software"}],"about":[{"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/types\/software"}],"wp:attachment":[{"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/media?parent=5348"}],"wp:term":[{"taxonomy":"software-product","embeddable":true,"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/software-product?post=5348"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}