{"id":6187,"date":"2026-11-11T07:28:49","date_gmt":"2026-11-11T06:28:49","guid":{"rendered":"https:\/\/dinamobesturing.nl\/nieuwsbericht\/important-update-for-oc32-and-rm-x\/"},"modified":"2026-11-11T07:46:44","modified_gmt":"2026-11-11T06:46:44","slug":"important-update-for-oc32-and-rm-x","status":"publish","type":"nieuwsbericht","link":"https:\/\/dinamobesturing.nl\/en\/nieuwsbericht\/important-update-for-oc32-and-rm-x\/","title":{"rendered":"Important update for OC32 and RM-x"},"content":{"rendered":"\n

New firmware is available for the OC32, RM-x and a new OC32Config:OC32Config 3.23<\/a>OC32 firmware 3.23<\/a>RM-C firmware 1.42<\/a><\/p>\n\n

For the release notes, check our Downloads pagina<\/a> under actuele firmware<\/a> and actuele software<\/a><\/p>\n\n

This is an important update because it fulfills two long-held wishes.TMxx Feedback<\/strong>It is now possible to send TM feedback in addition to OC feedback. A feedback is a sensor\/reporter used by the control software to trigger an event. Previously, it was already possible to link a feedback instruction to a pin and send it to the control software via OC32 feedbacks. For example, to report an end position or status. With this new option, it can also be done as a TM feedback address. You choose one of the free 128 addresses that have not been assigned to the TM44 or TM-H in an address range. This is useful for software packages that do not support OC32 feedback.Network Set aspect<\/strong>With this new instruction, it is possible to “jump” to another OC32 module in your network. Previously, you could only jump to another pin within the same OC32. If a part of your “device” was on a different OC32, it wouldn’t work. With the new firmware and software 3.23, this is no longer a problem!You add an instruction to an aspect and specify which pin of which OC32 should activate a certain aspect.<\/p>\n\n

This is particularly useful when, for example, you want to control a series of lights in a cycle, but not all lights are on the same OC. Or when a push button in a control panel needs to control a number of pins distributed across various OCs in your network.Updating your firmware<\/strong> and software<\/strong>To use this function, it is necessary to update both the RM-x to 1.42 and your OC32 modules to 3.23. There is also an update file for OC32Config.Software: Download OC32Config 3.23, extract the .zip file, and place the file in the extracted folder on your desktop or any folder on your computer. A small tip: remove the icon of the previous OC32Config from your desktop first.Firmware:These steps are fairly simple and are described in the manuals for the RM-C, RM-U, OC32, and OC32\/NG.In brief, the steps are as follows:<\/p>\n\n

    \n
  1. Open DinamoConfig and connect to your system (you can skip this step for the RM-x)<\/li>\n\n\n\n
  2. Set the RM-x to “Bootloader Transp. Mode” (you can skip this step for the RM-x)<\/li>\n\n\n\n
  3. Open AVRootloader software, which can be downloaded from our downloads page <\/li>\n\n\n\n
  4. Select the COM port of your RM-x<\/li>\n\n\n\n
  5. In the FLASH field, select your downloaded firmware file. This has the .acy extension<\/li>\n\n\n\n
  6. On the OC32, place a jumper over the RESET pins (you can skip this step for the RM-x)<\/li>\n\n\n\n
  7. Click “Connect device” in the software<\/li>\n\n\n\n
  8. On the OC32, remove the jumper in one smooth motion; on the RM-x, press the reset button next to the LEDs once briefly. Both the power and data LEDs (green and orange) will now be lit continuously<\/li>\n\n\n\n
  9. Now click “Program” in the software and wait until the log window appears. <\/li>\n\n\n\n
  10. Now click “Disconnect Device” in the first window<\/li>\n<\/ol>\n\n

    Repeat steps 6 through 10 for each OC32 module in your network.<\/p>\n\n

    Is it not working? Please contact your dealer; they can assist you with this.<\/p>\n\n

    <\/p>\n","protected":false},"featured_media":6197,"template":"","meta":{"_acf_changed":false},"nieuws-archief":[],"nieuws-tag":[],"class_list":["post-6187","nieuwsbericht","type-nieuwsbericht","status-publish","has-post-thumbnail","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/nieuwsbericht\/6187","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/nieuwsbericht"}],"about":[{"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/types\/nieuwsbericht"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/media\/6197"}],"wp:attachment":[{"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/media?parent=6187"}],"wp:term":[{"taxonomy":"nieuws-archief","embeddable":true,"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/nieuws-archief?post=6187"},{"taxonomy":"nieuws-tag","embeddable":true,"href":"https:\/\/dinamobesturing.nl\/en\/wp-json\/wp\/v2\/nieuws-tag?post=6187"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}